- Free shipping
Your cart is empty
Subtotal:$0.00
Never break an expensive headlight or fog light again! Xpel makes the best headlight protection kits on the market. With the average cost of replacement head lamps and fog lamps spiraling to nearly $300, it is nice to know that there is a product available to protect your car against the perils of the open road. Xpel Light Protection Products are made from a proprietary, scratch-resistant, urethane material coupled with the strongest optically clear 3M adhesive available. Designed for maximum durability, Xpel light covers were originally tested under the harshest of circumstances with amazing results. Both in the real world and in the lab, Xpel covers have proven that they will withstand a barrage of 1" diameter stones (about 1oz.) at speeds up to 120 m.p.h. with no damage to the lens they protect. Though the likelihood of this ever happening to your car in the real world is slim, it is nice to know that your expensive lenses are protected in any scenario. Xpel is so confident in their product that they offer a 5-year warranty to leave you with complete peace of mind. Additionally, Xpel headlamp protection kits can restore clarity to older vehicles with dulled or pitted headlamp lenses. Frequently Asked Questions "I have installed the kit on my headlights and they looked fine, but now they look foggy. Did I do something wrong?" When using the wet application technique, this is normal. The fog is the result of the alcohol/water solution evaporating from beneath the plastic. The water vapor that is produced results in a hazy appearance for several days. The haze will clear as the vapor dissipates. "Is it best to apply your light protection kit to the lenses wet or dry?" We have found that the wet installation yields the best-looking installation with the least amount of difficulty in most cases. On larger headlamp pieces, bubbles and improper alignment of the material are far less likely using the wet installation method. However, on smaller pieces, such as fog lamps, the dry installation method is sometimes easier. This is especially the case if the lamp is spherical in shape. "The lights on my car are heavily contoured. Is your kit hard to install on this type of light or should I have them professionally installed?" Xpel headlamp protection material is extremely pliable and can easily be contoured over dome shaped surfaces. Professional installation should not be necessary provided that you follow the instructions closely. If you still feel uncomfortable attempting installation on your own, we can locate an installer near you. "I have the headlamp kit almost completely applied using the wet application method, but I can't seem to get the edges to completely stick down. What am I doing wrong?" It is absolutely imperative that a hairdryer or heat gun is used in this area to seal the edges. The heat serves two purposes. First, it helps evaporate the remaining alcohol/water solution from under the edges, and second it makes the plastic more pliable so that it can contour to the edge of the light. Be careful if you are using a heat gun to warm the plastic. It takes only a small amount of heat to apply the material. If you apply too much heat you can damage the surface of the plastic. "What if I want to remove the shields at a later date?" The removal process is just a matter of warming the plastic, and peeling them off. They will require some muscle to get them off, but they normally peel off without any residue left on the lens. If any adhesive at all remains behind, it may be removed by simply rubbing it with your thumb. The adhesive will then ball up and roll off. Kit Options HL Headlamp Kit SL Signal Lamp Kit FL Fog Lamp Kit Note: If your vehicle is not listed, e-mail us and we will check on availability. Kits also available in blue, yellow, and smoked colors. Contact us to inquire about pricing.
Never break an expensive headlight or fog light again! Xpel makes the best headlight protection kits on the market.
With the average cost of replacement head lamps and fog lamps spiraling to nearly $300, it is nice to know that there is a product available to protect your car against the perils of the open road. Xpel Light Protection Products are made from a proprietary, scratch-resistant, urethane material coupled with the strongest optically clear 3M adhesive available. Designed for maximum durability, Xpel light covers were originally tested under the harshest of circumstances with amazing results. Both in the real world and in the lab, Xpel covers have proven that they will withstand a barrage of 1" diameter stones (about 1oz.) at speeds up to 120 m.p.h. with no damage to the lens they protect. Though the likelihood of this ever happening to your car in the real world is slim, it is nice to know that your expensive lenses are protected in any scenario. Xpel is so confident in their product that they offer a 5-year warranty to leave you with complete peace of mind. Additionally, Xpel headlamp protection kits can restore clarity to older vehicles with dulled or pitted headlamp lenses.
Frequently Asked Questions
"I have installed the kit on my headlights and they looked fine, but now they look foggy. Did I do something wrong?"
When using the wet application technique, this is normal. The fog is the result of the alcohol/water solution evaporating from beneath the plastic. The water vapor that is produced results in a hazy appearance for several days. The haze will clear as the vapor dissipates.
"Is it best to apply your light protection kit to the lenses wet or dry?"
We have found that the wet installation yields the best-looking installation with the least amount of difficulty in most cases. On larger headlamp pieces, bubbles and improper alignment of the material are far less likely using the wet installation method. However, on smaller pieces, such as fog lamps, the dry installation method is sometimes easier. This is especially the case if the lamp is spherical in shape.
"The lights on my car are heavily contoured. Is your kit hard to install on this type of light or should I have them professionally installed?"
Xpel headlamp protection material is extremely pliable and can easily be contoured over dome shaped surfaces. Professional installation should not be necessary provided that you follow the instructions closely. If you still feel uncomfortable attempting installation on your own, we can locate an installer near you.
"I have the headlamp kit almost completely applied using the wet application method, but I can't seem to get the edges to completely stick down. What am I doing wrong?"
It is absolutely imperative that a hairdryer or heat gun is used in this area to seal the edges. The heat serves two purposes. First, it helps evaporate the remaining alcohol/water solution from under the edges, and second it makes the plastic more pliable so that it can contour to the edge of the light. Be careful if you are using a heat gun to warm the plastic. It takes only a small amount of heat to apply the material. If you apply too much heat you can damage the surface of the plastic.
"What if I want to remove the shields at a later date?"
The removal process is just a matter of warming the plastic, and peeling them off. They will require some muscle to get them off, but they normally peel off without any residue left on the lens. If any adhesive at all remains behind, it may be removed by simply rubbing it with your thumb. The adhesive will then ball up and roll off.
Kit Options | |
HL | Headlamp Kit |
SL | Signal Lamp Kit |
FL | Fog Lamp Kit |
Note: If your vehicle is not listed, e-mail us and we will check on availability. Kits also available in blue, yellow, and smoked colors. Contact us to inquire about pricing.
Shipping
We utilize UPS, Fedex, and USPS for all of our shipping needs. Carrier choice is based upon availability and needs of the customer and is the sole discretion of PFYC. We always try to ship within 24 hours of order placement (do to the custom nature of some products, shipping within 24 hours is impossible, actual shipping time frames will be listed in the product description). Please keep in mind that some products such as Custom Fit Car Covers, Lloyds Floor Mats, Painted accessories, and Racemesh Products can take 3 -10 days to ship and are charged at time of order placement. Racemesh products take 4 weeks to ship as they are made to order.
Sometimes a product needs to be returned. Our goal is to make this process as painless as possible. If you receive a product that is incorrect, damaged or inferior, please contact us immediately so we can begin the returns process and make sure you receive what you ordered quickly. For all returns, you must receive a Return Merchandise Authorization (RMA) number.
When you send back an item you no longer want, you have two choices for getting credit, assuming you properly followed all guidelines for returns:
You've Changed Your Mind
If you have ordered and received an item from PFYC.com that you no longer want, please follow the directions in the Returning Items section below. Please note that you are responsible for return shipping, and we will not reimburse you for the original shipping cost.
Incorrect or Damaged Product
If you have received damaged merchandise or have received items that you did not order, please contact us by replying to your e-mail receipt, making sure to copy the contents of the receipt in your e-mail. Simply let us know the error or that the product was damaged, and we'll take care of it at no cost to you, including all shipping charges (up to the original amount you paid for shipping). We will wait to receive and inspect the originally-shipped product prior to shipping a replacement. If a product was damaged during shipping, you must retain all materials until the shipper (UPS, FEDEX, etc.) has had a chance to inspect the package, if they choose. Our policy is to replace damaged or incorrect products. If you choose not to accept a replacement, it is considered a regular return and subject to our return policy guidelines listed above.
Replacement Product
If we sent you something in error, and we send the correct item out but do not get the wrong one back within 10 business days, we will charge your credit card for the full amount of the replacement item or the incorrect item plus shipping, whichever is greater.
Warranty Replacement
If you feel a product you have purchased is defective or has failed under warranty, contact us. We will help determine the likelihood it is defective prior to your returning the product for inspection. This will save you time and money if there happens to be another reason for the problem you are having with the product. Once a product has been determined it may be defective and requires further inspection, we will instruct you as to your next course of action. This next step may vary depending on the guidelines set forth by the manufacturer. Shipping costs for returning parts for inspection and returning the part to you are usually your responsibility depending on the manufacturer and what their warranty policy is. More information can be found in our Customer Service section under the Product Warranties section.
Follow the steps below to return items that you no longer want:
If you have any questions about our return policy, please contact us.