Your next upgrade pays you back.PFYC Rewards · 1pt per $1 spent · Details →
PFYC Rewards1pt per $1 spentDetails →

INSTANT SAVINGS!
PFYC5: $5 OFF ORDERS OVER $125 - PFYC25: $25 OFF ORDERS OVER $275 - PFYC50: $50 OFF ORDERS OVER $550
These Coupons Are Only Available For Online Purchases

Electric Exhaust Cutouts: How They Work, What Size to Buy and Where to Install

:

Clear
Clear
Nov 1, 2026

An electric exhaust cutout is the simplest way to get two personalities out of one exhaust system. With the valve closed, the car stays quiet and fully muffled for the drive to work. Flip a switch on the dash and the exhaust exits ahead of the mufflers, giving you an open header sound at the drag strip, on a track day or at a cruise night, without crawling under the car with a wrench to pull a cap.

We sell a lot of Quick Time Performance cutouts at PFYC, and most of the calls we get about them come down to the same handful of questions: how they work, what size to order, whether you need one valve or two, and where the cutout should be welded in. Here are straight answers to each.

Quick Time Performance electric exhaust cutout with stainless steel Y pipe

How an Electric Exhaust Cutout Works

A cutout is a valve mounted on the short branch of a Y pipe that is welded into your existing exhaust. Inside the valve is a butterfly plate. When the plate is closed, it seals off the branch and the exhaust continues through the converters and mufflers exactly as it does today. When the plate opens, exhaust gas takes the path of least resistance and leaves through the short branch instead of the full system.

On an electric cutout, a small DC motor turns that butterfly, and you control it from a switch inside the car. The Quick Time electric exhaust cutout uses a valve body machined from 6061 aluminum, a stainless steel butterfly plate and shaft, and a high torque, gear driven motor. The harness uses mini weathertight connectors, which matters on a part that lives under the car in rain, road salt and heat.

Electric Cutout vs Manual Cutout

A manual cutout is usually a bolt on cap or a cable operated gate. It works, but opening a cap means getting under the car with tools every time, and you cannot close it again until you stop. Cable cutouts are better, though cables stretch, corrode and bind over time. An electric cutout costs more up front, but you can open and close it from the driver seat in a parking lot, at the staging lanes or rolling down the road, and there is no linkage to adjust. For a car that gets driven, electric is the version people end up glad they bought.

Round or Low Profile Oval?

The standard round valve is the strongest choice for most cars and trucks with normal ground clearance. On a lowered car, a Corvette, a Camaro or anything that already scrapes on driveways, the motor housing on a round valve can hang lower than you want. That is where the Quick Time low profile oval electric exhaust cutout comes in. Its flatter body tucks up closer to the floor pan and fits 2.25 to 3 inch exhaust, so you get the same switch controlled sound without giving up ground clearance.

Quick Time low profile oval electric exhaust cutout for lowered cars

What Size Exhaust Cutout Do You Need?

Measure the outside diameter of the exhaust pipe at the exact spot where the cutout will go, and order that size. Do not go by the size of the tailpipe tips or the size printed on a muffler box, because those are often different from the pipe in the middle of the system. Quick Time single valves cover 2.25 to 2.5 inch pipe with one valve, and 3 inch and 3.5 inch systems each have their own size. If you do not already have a weld in tee, add the matching 304 stainless Y pipe when you order so the valve and pipe are sized to each other.

Do You Need One Cutout or Two?

If your car has a single exhaust, or a dual system that joins through an H pipe or X pipe ahead of where the cutout will sit, one valve does the job. A true dual exhaust with completely separate left and right pipes needs a valve on each side, or one bank will stay muffled while the other opens. Dual kits open both valves together from a single switch. The Quick Time dual low profile oval cutout is the go to for low cars running true duals, and it can be paired with an optional electronic controller if you want to stop the valves part way for a milder tone.

Quick Time dual low profile oval electric exhaust cutout kit

Where to Install an Electric Cutout

The cutout needs a straight section of pipe with enough room around it for the motor housing. Most installs place it after the headers or collector, and the closer it is to the engine, the louder and rawer it sounds when open. On any street registered vehicle, keep the cutout after the catalytic converters. A cutout ahead of the cats is for dedicated race and off road vehicles only. Any exhaust shop can weld in the Y pipe in short order, and the valve then bolts to the flange.

A few details make for a cleaner install. Keep the valve and wiring away from fuel lines, brake lines and the starter. Make sure the open branch is not pointed at the floor pan, a tire or a fuel tank, and add a short turndown if needed. Route the harness along the frame, away from the exhaust, and mount the switch where you will not bump it by accident.

Is an Electric Exhaust Cutout Street Legal?

The cutout itself is just a valve. What matters is how you use it. Many states have noise laws and rules against exhaust that is louder than stock, and running open on public roads can earn you a ticket. Federal rules also prohibit removing or bypassing emissions equipment on street vehicles, which is why the cutout belongs after the converters on anything with a license plate. The practical answer is to drive closed on the street and open the cutout where it is allowed, such as the track, the strip or private property. Check your local laws before you install.

Want It Built Into a Cat Back System?

If you are replacing the exhaust anyway, some systems come with the cutout already built in. The aFe Gemini XV cat back exhaust with cutout for the 2019-2021 Silverado and Sierra 1500 V8 is a 3 inch, 304 stainless system with an integrated valve, so you get the dual mode sound in a bolt on package without a separate weld in tee. aFe also offers Gemini XV systems for 2014-2019 GM trucks.

aFe Gemini XV cat back exhaust with built in cutout for Silverado 1500

Electric Exhaust Cutout FAQ

Will an electric cutout hurt my engine?

No. With the valve closed, the exhaust works exactly as it did before. With it open, the engine simply sees less back pressure. Many owners notice a stronger pull at wide open throttle with the cutout open.

Will it trigger a check engine light?

Installed after the catalytic converters and downstream oxygen sensors, a cutout does not change what the sensors read, so it should not set a code. Mounting it between the engine and the rear sensors can affect readings, which is another reason to keep it behind the converters.

Can I leave the cutout half open?

With the optional Quick Time electronic controller, yes. You can run the valve fully closed, fully open or anywhere in between, which gives you a deeper tone around town without going all the way to open header volume.

Is the Y pipe included?

Only when you select it. The stainless steel Y pipe is offered as an option in single or dual form, sized to match the valve, and it can also be ordered by itself if you are replacing a worn one.

Shop Electric Exhaust Cutouts at PFYC

PFYC has been selling performance parts since 1998, and we stock Quick Time single, dual and low profile cutouts in every common pipe size. If you are not sure which valve or Y pipe fits your car, call our team at 866-695-7392 with your year, make, model and pipe size, and we will help you get the right kit the first time.