X-Pel Invisible Headlamp Protection

X-Pel Invisible Headlamp Protection

Item Code: GN8005

Low Price Guarantee!

FREE SHIPPING in the Lower 48 states! Half price shipping to Canada.

In Stock


Product Description

Never break an expensive headlight or fog light again! Xpel makes the best headlight protection kits on the market.

With the average cost of replacement head lamps and fog lamps spiraling to nearly $300, it is nice to know that there is a product available to protect your car against the perils of the open road. Xpel Light Protection Products are made from a proprietary, scratch-resistant, urethane material coupled with the strongest optically clear 3M adhesive available. Designed for maximum durability, Xpel light covers were originally tested under the harshest of circumstances with amazing results. Both in the real world and in the lab, Xpel covers have proven that they will withstand a barrage of 1" diameter stones (about 1oz.) at speeds up to 120 m.p.h. with no damage to the lens they protect. Though the likelihood of this ever happening to your car in the real world is slim, it is nice to know that your expensive lenses are protected in any scenario. Xpel is so confident in their product that they offer a 5-year warranty to leave you with complete peace of mind. Additionally, Xpel headlamp protection kits can restore clarity to older vehicles with dulled or pitted headlamp lenses.

Frequently Asked Questions

"I have installed the kit on my headlights and they looked fine, but now they look foggy. Did I do something wrong?"
When using the wet application technique, this is normal. The fog is the result of the alcohol/water solution evaporating from beneath the plastic. The water vapor that is produced results in a hazy appearance for several days. The haze will clear as the vapor dissipates.

"Is it best to apply your light protection kit to the lenses wet or dry?"
We have found that the wet installation yields the best-looking installation with the least amount of difficulty in most cases. On larger headlamp pieces, bubbles and improper alignment of the material are far less likely using the wet installation method. However, on smaller pieces, such as fog lamps, the dry installation method is sometimes easier. This is especially the case if the lamp is spherical in shape.

"The lights on my car are heavily contoured. Is your kit hard to install on this type of light or should I have them professionally installed?"
Xpel headlamp protection material is extremely pliable and can easily be contoured over dome shaped surfaces. Professional installation should not be necessary provided that you follow the instructions closely. If you still feel uncomfortable attempting installation on your own, we can locate an installer near you.

"I have the headlamp kit almost completely applied using the wet application method, but I can't seem to get the edges to completely stick down. What am I doing wrong?"
It is absolutely imperative that a hairdryer or heat gun is used in this area to seal the edges. The heat serves two purposes. First, it helps evaporate the remaining alcohol/water solution from under the edges, and second it makes the plastic more pliable so that it can contour to the edge of the light. Be careful if you are using a heat gun to warm the plastic. It takes only a small amount of heat to apply the material. If you apply too much heat you can damage the surface of the plastic.

"What if I want to remove the shields at a later date?"
The removal process is just a matter of warming the plastic, and peeling them off. They will require some muscle to get them off, but they normally peel off without any residue left on the lens. If any adhesive at all remains behind, it may be removed by simply rubbing it with your thumb. The adhesive will then ball up and roll off.

Kit Options
HL Headlamp Kit
SL Signal Lamp Kit
FL Fog Lamp Kit

Note: If your vehicle is not listed, e-mail us and we will check on availability. Kits also available in blue, yellow, and smoked colors. Contact us to inquire about pricing.

Installation Difficulty

Installation Difficulty 2 View Installation Instructions


★★★★★ ★★★★★
3.67/5 Stars out of 3 Reviews
Had an isue BUT PFYC to the rescue !
Keith (Long Island, NY USA) | May 1st, 2014
Had an issue with a spot that didn't dry underneath the film. I contacted Xpel who said to deal with PFYC (?). Mike at PFYC was GREAT. Resolved the issue. I can't say enough good things about the customer service at PFYC. I've purchsed from them in the past and will continue to do so in the future. Customer service, quick delivery, good prices! Hey that's the whole package, right?
Easy to install and a necessary addition to the car
Jim C (Fort Gratiot, MI USA) | June 4th, 2013
I drive a lot of miles each year and always have issues with the headlights getting "sand blasted". Picked up some of these for my 2013 Mustang and it was easy to install and the headlights actually look better with the protectors on them. Definitely worth getting, I could already see that the headlights were starting to show some pitting. The only issue I had was the smaller protectors for the fog lights. They are obviously for the GT grille given the size so don't fit the GT/CS or MCA smaller fog lights in the bumper.
2 separate pieces for each 09-13 TSX headlight!?
Mike (Spring, TX USA) | January 17th, 2013
disappointed that xpel would make 2 pieces for each headlight instead of just cutting them out properly. Great product just not executed well for my car. I've bought these for 4 other cars Mazda3, Prius, A5, Corvette and never seen this before.
Write a Product Review